Saturday, August 27, 2016

How to Remove and Install Garage Door Weather Seal

-->
SAFETY FIRST! Be very careful around the garage door. It’s one of the heaviest moving objects on your house and can inflict serious or even deadly injury and harm to people, pets and objects in and around the garage.

Getting Started
Start by placing all of the necessary tools outside of the garage (on the driveway, etc.) because you will need to close the garage door when you begin the weather seal removal and installation process.
Recommended Tools Needed:
·      Safety glasses and work gloves
·      Utility knife with a NEW, sharp blade
·      Tape measure
·      Vice Grips and/or locking pliers or clamps
·      Pencil
·      Drill and a 1/16” drill bit
·      New garage door weather seal (available at www.stardoorparts.com)
·      Utility Shears or other means to cut the weather seal
·      Hammer
·      Nails
·      Caulk gun
·      Caulk (we suggest using one that is paintable so you can match it to the color of your house or garage door)
·      Clean cloth
·      Household spray cleaner (such as 409)
·      An Assistant!


Removal of the Old Weather Seal
1.     Start by closing the garage door and unplugging the garage door opener from the power source. Also, if your opener is equipped with an emergency operator trolley release (usually a red T-style pull handle on a rope connected to the trolley), be sure to pull the release to disengage the trolley from the track and manually raise the garage door to the open position.  We have found that it is easier to work on the weather seal with the garage door in an open position.  To do this hold the garage door where you desire it to stay and use a locking pliers (Vise Grips) and clamp it to the garage door track. 

Tip: Be sure to position the locking clamp below the bottom roller so that the door cannot close on you if the torsion spring tension happens to be out of adjustment. This is a very common issue and the tension should be adjusted annually only by a trained professional.

2.     To begin removal of the old weather seal, (with the garage door in an open position), choose a side and take a sharp utility knife (with a NEW blade) and make a clean score at the joint between the weather seal body (wood, aluminum, PVC, or vinyl) and the garage door jamb (see photo).  This will allow you to remove the old weather seal with out damaging the finish on the garage door jamb.

3.     Using a rigid, steel putty knife, firmly push between the old weather seal and the garage door jamb. With a gentle prying motion, loosen the weather seal from the door jamb. Now you will be able to use a flat bar (pry bar) inserted in the gap to finish removing the seal and nails.



Tip: You may want to place a small piece of sheet metal or a putty knife under the pry bar to prevent damaging the finished garage door jamb (see photos).





4.     Repeat this process for the remaining top and side pieces of weather seal.

5.     With all of the weather seal and fasteners removed from the garage door jambs, take this opportunity to remove any debris and ridges of paint.  We also suggest cleaning the door jambs with a clean cloth and some household spray cleaner (like 409 or a similar product that cut remove dirt and grease).
Installation of New Weather Seal
1.     Start by using a tape measure to measure the length of the inside of the top garage door jamb, side-to-side at the top, where the top piece of garage door weather seal will be installed first (see photos).

Tip:  This step is done much easier with two people. 


2.     Use a utility shears to cut the new, replacement weather seal pieces to length (be sure to first check the fit and adjust as needed and re-measure BEFORE cutting!).
Tip:  You can use utility shears, a hand or electric hand saw with a fine tooth blade (placed in a miter box based on type of saw used), an angle grinder with a 3/32” cutoff wheel, or a multi-tool with a fine tooth blade or saw. There are many options to choose from here, just remember to utilize ALL SAFETY MEASURES regarding eye wear, hearing protection, gloves, etc.

3.     After you have determined the placement of the new, cut weather seal, we recommend drilling small pilot holes for the nails.  We have found that it is easier to drill a small pilot hole (slightly smaller than the diameter of the nail you will use) centered in the width of the new weather seal, 1 inch from each end and then in 8” – 12” inch intervals for the entire length of weather seal.  This eliminates the need to try to pound the nails in while in an upside down position (see photo).

Tip:  If it is colder than 60 degrees F outside we highly recommend that you take the time to drill small pilot holes especially if you are installing PVC seal and the main body cracks easily at colder temperatures.


4.     Next, push a nail into each hole in the weather seal. We prefer to use color matched Maze brand galvanized, smooth or ring shank trim nails, but a stainless steel or 4D, (about 1-3/8” to 1-1/2” in length) galvanized box nails should work as well.  Do not use steel nails of any type as they will rust and leave rust streak on the paint and finishes.

Photo Notes:  Nails shown in photo, left to right, are: Galvanized Brown Maze Ring Shank Nail, Galvanized White Maze Ring Shank Nail and Stainless Steel Smooth Shank Nail.  The 4D Galvanized Smooth Shank Box Nail is not pictured.

5.     With the door in the closed position, and with the help of your assistant, raise the weather seal into position, making sure to adjust the lip of the seal so that it presses against the face of the garage door, forming an air tight seal. The solid PVC body of the seal should not contact the garage door.

6.     Start all of the nails across the top piece of weather seal into the door jamb, but do not drive the nails all the way in until you have made your final adjustments to the weather seal placement (see photo).

7.     Repeat the same process for both of the side door jamb weather seals, adjusting the weather seal fit as you go.
8.     Next you can trim the soft vinyl flaps at a 45 degree angle in the corners for a nice, clean-looking finish.
9.     Check the garage door operation to make sure it does not bind on the weather seal at any point as it travels along the track.

10.  Now you can drive the weather seal nails all the way in, just be careful not to hit the door if you have it closed at this time.
11. If you had problems with binding before you replaced the seals, you may find that you will need to adjust the garage door operator pressure limit settings.  Refer to your garage door operator Owner’s Manual or their website for this information.
12. Finally, for a nice clean appearance and to seal-out the weather elements, we recommend using a latex, silicone-based but paint-able caulk, to seal along the edge of the weather seal and the door jamb.  Be sure to use a damp rag to wipe away any excess caulk.  You can then apply touch-up paint as needed.
If you aren’t sure what weather seal to buy at www. stardoorparts.com, simply write us at sales@stardoorparts.com and we will try to help and get what you what need quickly and at our low prices.  Also be sure to check out our other Garage Door DIY Articles on our website.





Monday, August 22, 2016

Helpful Tips on Hiring Home Contractor

How to Hire a Local Contractor

Whether you are looking to hire a contractor to install new rollers on your garage door or build an addition to your garage, it's important to hire a licensed contractor that is also experienced in their field. Here are some helpful tips to keep in mind:

1.  In most every state it is the law that any contractor who advertises MUST be licensed, no matter the size of the job. So look and ask for a license number and check it online at your states registrar of contractors or equivalent site.   Once on the site, enter the company license number. Note the name of the company (does it match the name of the company being advertised?). Also verify if they have worker’s compensation insurance. If they say they don’t, ask when you call them, who will be coming out. If it’s the name (of the individual/owner) on the license, no problem. If it is a technician, or any other name don't do business with them since said they didn’t have employees!  You now know that whoever would come out to perform the work is not licensed or insured. They will say they are sub contractors but they are not.  You can also look to see if they have any complaints and if their license was ever revoked or suspended and why. Stay away from any contractor which you has any unresolved matters with the state licensing agency.

2.  Check the your local Better Business Bureau (BBB). Contrary to a mixed news reviews that debunked their credibility, they actually are a very credible source. They will have online reviews and records that you can search that include contractors who are not even members of the BBB. You can see how many and what type of complaints weed files and how long ago they were and what the resolution was. Make sure whoever you hire has a good rating. It takes a lot of accountability to maintain a good rating over the years.

3.  Use the following web sites and look for reviews: Google and Yelp. Simply type in the company or contractor name and then add the word "reviews" to the search and you should get a list of most reviews on the web.

4.  If you have several projects to do, Angie’s List is a great resource for contractors.  A company can’t get on Angie’s List directly. Their clients have to refer them. This is like having a giant data base of reviews for contractors in various specialties in your area. There’s a small annual fee but worth it if you may need to do multiple searches.

Now, hopefully these tips will help you make an informed decision about any contractor or company you hire in any of the trades! Taking 15 minutes to check things out will give you a good sense of the company and could save you time and money!

Tuesday, August 16, 2016

Check Out Our New Website!


Star Door Parts just launched a completely new and redesigned website to enhance your shopping experience. We are still the same company that you have come to trust with our outstanding customer service, fast shipping, low prices and comprehensive inventory and product selection.

While redesigning our site we listened to your feedback and worked to provide you an even better online shopping experience. Specifically changed was our mobile site. Our new site is responsive to the devise you are using which means that the website will look different on a smartphone, tablet and desktop. The navigation is now easier since the mobile site automatically adjusts the site view to your phone screen size and position held. If you still need the full features of our desktop site but are using a mobile device, simply use your browser option to Request Desktop Site from either your Safari or Chrome browser menu.

We appreciate your business and welcome any continued feedback on our website design, product offerings, blogs, etc.

The Team at Star Door Parts

https://www.stardoorparts.com/